Where Does Step Flashing Go On A Roof

How To Roof A House Diy Roofing Roofing Home Construction

How To Roof A House Diy Roofing Roofing Home Construction

Pin On Roof Details

Pin On Roof Details

Pin On Home Improvement Stuff

Pin On Home Improvement Stuff

Pin On Back Porch

Pin On Back Porch

Pin On Roofing

Pin On Roofing

Pin On Darn Roof

Pin On Darn Roof

Pin On Darn Roof

Step flashing is a rectangular piece of flashing bent 90 degrees in the center.

Where does step flashing go on a roof.

Bent into an l shape. The bottom edge of the flashing should extend just below the nail line. Step flashing steps up a roof to protect where the roof meets the side walls of dormers chimneys and some skylights. It is used for roof to wall flashing.

Pieces of step flashing are bent at an angle relative to the roof pitch and installed along the full length of the sidewall where it joins the roof deck. The top requires another custom piece. This process will continue up the entire roof. Next install the step flashing with the next course of shingles over top of it.

Attach each piece with a single nail high enough to be covered by the next course of flashing the building wrap and the siding. Galvanized sheet metal bent at a 90 degree angle i e. Each section is worked into a course of shingles so that it overlaps the section beneath it. Continuous flashing is sometimes seen where a roof meets a sidewall but in the long run step flashing will do a better job of preventing water leaks.

Step flashing needs to turn up a minimum of three inches up the sidewall. The flashing material should be 4 inches by 7 inches in length when it lies on the roof deck. The flashing s vertical edge is usually tucked under siding or capped with a. Posted march 4 2017 filed under roof installation roof repair maintenance.

The 7 inch length ensures a 2 inch headlap on. Step flashing should always be used where the roof deck meets a sidewall. It is used for roof to wall flashing. Step flashing is used to provide a water tight connection where roofing adjoins a vertical juncture.

Multiple pieces of the flashing will be installed in layers with shingles to ensure the water flows away from the wall. It consists of a series of right angled metal pieces. Each piece of step flashing laps over the shingle below and under the shingle above. The flashing should be partially exposed along the wall.

Pin On Contractor Tips

Pin On Contractor Tips

Pin On Roof

Pin On Roof

Pin On Building Science

Pin On Building Science

Pin On Roof

Pin On Roof

Pin On Diy And Crafts

Pin On Diy And Crafts

Pin On Destinasi

Pin On Destinasi

Pin On Roof

Pin On Roof

Pin On Framing

Pin On Framing

Pin On Water Proofing

Pin On Water Proofing

Pin On Projects Garage

Pin On Projects Garage

Pin On Construction

Pin On Construction

Pin On House

Pin On House

Pin On For The Home

Pin On For The Home

Pin On Week 6

Pin On Week 6

Pin On Are Test Prep

Pin On Are Test Prep

Pin On Infinite Roofing

Pin On Infinite Roofing

Pin En Roof

Pin En Roof

Pin On Home Improvment

Pin On Home Improvment

Https Encrypted Tbn0 Gstatic Com Images Q Tbn 3aand9gcthk Radxm Tk9mzfeyuebbcb2ixkn Qb9tqeefvpnyzzhcgtfz Usqp Cau

Https Encrypted Tbn0 Gstatic Com Images Q Tbn 3aand9gcthk Radxm Tk9mzfeyuebbcb2ixkn Qb9tqeefvpnyzzhcgtfz Usqp Cau

Pin On Projects

Pin On Projects

Sealing Structural Penetrations At Roof Wall Intersections Roofing Roof Repair Diy Roof Repair

Sealing Structural Penetrations At Roof Wall Intersections Roofing Roof Repair Diy Roof Repair

How To Re Shingle A Roof And Not Die Diy Roofing Roofing Home Improvement Projects

How To Re Shingle A Roof And Not Die Diy Roofing Roofing Home Improvement Projects

Pin On Flashing

Pin On Flashing

Pin On Roof Flashing Showcase

Pin On Roof Flashing Showcase

Source : pinterest.com